Видео

I noticed the square hole on the baffle, mine had that hole and I lost suction and it wasn't lifting the grass on that side. I put a bolt in and fixed the problem! Changed, belt, blades and was going to change spindles as nothing was fixing the problem. Then I noticed the hoke and fifty cent fix. Anyhow, did you have that issue with that hole aswell? It was a strange thing to happen

Hi, I like your cover seats. Can you tell me where I can buy some too? Thanks

Very cool. (pun intended). I'm going to put some of this in and then engineer something to capture the heat from the top and recirculate it for the winter months when I get a lot more direct sun when the leaves are gone. Something to try in my copious free time :)

Video was very helpful. Just did mine with same parts you did. Cranked right up on first pull. Thanks again 👍

thanks alot

How do you release the hydrostatic transmission/put it in nuetral on a tigercat 2? I can find a video for pretty much any zero turn but a tigercat 2...

Mind posting a link to this exact one? Also, mind doing a vid of how it installs and opens/closes? THANKS!

Are you aware that you installed that incorrectly? You need an air gap. Needs to be stapled to the rafters not the roofing board or you create thermal bridging.

If buying door replacement speakers go though sonic electronix. They will give you the plastic mounts with your purchase!

I have one just like yours. I'm having trouble getting the bolts off to pu a new bit in

You have no lockdown cable?

After a season, how do you feel about the mower? Still going well?

Yeah how do you get the top of the sail panel to stick? My problem is air gets in and expands the sale panel on the original. Glue? If so what kind?

After 3 years of use I am having issues with overload protection kicking in after 30 minutes of use. Anyone else experiencing this?

31 % vinegar bad ass stuff, using and boy does it work like a charm

Thank You for Sharing !!! 😊

I just bought this washer but when I use fabric softer it ends up at the bottom of the tub after the load is done and it’s all over my clothes so I have to run a rinse and spin cycle to dissolve it before I can put it in the dryer. Any suggestions? I’m putting the softner in the agitator where it says to put it and I’m only using 2 tablespoons

Mine constantly jams, the nails overlap each other in the magazine I have no idea why? Any help would be great. I have been using 50mm nails someone told me to use nothing over 25mm?

Hi, did you do a "follow-up" video to show how well this Sceptor worked?

i tried wit scrub rust was still there. i will try again wit ur method. also does it work for oil on asphalt driveway?

Thank you so much.

Great job, 👍 most people over tighten and when the hub warms up the bearing is too tight.

I have a 2002 crvwpuld you know where it's located? The inertia? N if so could you post a photo because I. SO unsure what it looks like cuz different videos say it looks like this or that and yah it's all different. Please help

Dude ur more focused and excited about the knock out plate more than the actual install and button. Like if Christopher Walken where to tell u he would be like "my guy.. u got it all wrong.. it's the wrong tone.. focusin on the wrong things...get to the install already.. if u mention the KNOCK out plate again..then ima knock u out and stab u n the face with a soldering iron!. Now get back to work.." So yeah beware of using the wrong tone with Mr. Walken..

I know this is an old video but what did the fox to your problem end up being? There is a later video of a flowmaster install where it’s running good again. My 89’GT is starting to do the same things your car was and any advice would be much appreciated. 🙏

Thank you for your modesty👍🏾 Dude , that thing is beautiful

Great. These short videos. Are helpful. Thank you. I have a jumper wire. I will replace the inertia switch first before I replace the electrical wire harness. I've already changes the fuel pump and fuel filter. In addition to the fuel relay fuse which was blown. Thank you.

Okay..... Where does the inertia switch wiring come from? Mine has been removed, where does the wiring originate?

Thank you!!!!

I just ordered a front set from luckyman and have watched a few install/ review videos. They all look good, but they all have the little imperfections you mentioned due to improper install. I'm so glad I found this video and now I'm even more excited for my covers to arrive. I'm now confident that they'll look amazing

Thank you very much for unearthing the mystery. Cannot believe that samsung can be this dumb at the design!!

use iodized salt for maximun letallity

Just finished bluing a Remington model 12. Bluing wouldn’t take and looked horrible. If you heat the metal it seems to go on better. I used a lot of bluing solution and used scotch brite soaked with bluing to scrub it into the metal. Many applications later and I called it done. Doesn’t look like original bluing but it’ll do. Thanks for the video! Any information you can get helps with this stuff.

"you probably got to this point" Ummm, as a matter of fact... :). Perfect video

I thought there was a bug on my screen lol

building cinder blocks instead of wood is cheaper right?

Is the 4"x4" beam too light to carry a 5.5' gate? Did you consider using a 4"x6" or 6"x^6?

My neighbor had an old commercial Honda unit that he literally wore the deck out on. Wore completely through the deck and it was all cracked out. Probably had a million miles on it

I rented one from Home Depot and the trimmer head straight up flew off while I was using it 😬 I'm guessing that a previous renter was rough on it when attempting to change the line, and weakened the plastic clips

That’s not a truck

0:08 0:12

Perfect, thanks.

Your the man! I assume the same is similar for a 88 bronco ii? I think it's under the steering wheel tho

Same here in North Carolina bruh! Takes longer to pick up the sticks and rocks than it does to mow 5 acres, easier to just mow them and change the blades every year! Appreciate the video!

many thanks!

Why is the gas tank so... microscopic?

I have a 5.0 and it's not even cranking it just stopped on me replaced the starter no difference I'm not sure what exactly it is anything would help! Thx

What mowing? Rocks?

Where can someone buy these blocks fur construction? What is the name of the material? I’m interested in building my own home

Is this your house you built?